Do it several time to test and see if its the ignition. The tabs (2) on the ignition switch must be seated inside the lock cylinder housing (1) for proper installation.
Take off pumkin cover, on center pin in the diff there is a bolt on the botton of the bigger opening that holds pin in place, take the bolt out of the pin and tap the pin out.
How to replace ignition switch on 2004 chevy silverado. Oe replacement for 2000 2002 chevrolet silverado 1500 ignition switch base custom ls lt wt com. Part 1 ignition switch circuit wiring diagram 2000 v8 chevrolet silverado gmc sierra. Some have a clip to pull too.
It takes an extra deep socket designed for that switch that can be purchased at any auto supply. To replace an ignition switch, you'll need to either have your old switch rebuilt by a dealership so you can keep your old keys or purchase a new switch from a dealership and get a new set of keys. This product is designed and tested to ensure the ultimate in durability and functionality.
Thanks and holler if you need. Try to get a jump from a friend and see what happens, does the same, faulty starter, may need replacing, try to use small hammer and tap lightly on the starter couple time and have a friend start the car while you tap lightly on it. Chevy silverado 2004, ignition switch by wve®.
Insert the ignition switch into the lock cylinder housing. Plug the wiring connector into the new switch. Make sure the white plastic gear is in the same position on both switches.
2004 chevy silverado 2500hd 4wd 8.1 start ebgine 4wd dash indacator goes out goes back to two wheel drive dash gauges and radio go out i replaced the ignition switch if you hold the key in stat positi. Ok,pushrod answered this 23 days ago. The most recently reported issues are listed below.
How to replace ignition switch chevrolet silverado 2004. Either way, you should remove your old ignition switch by taking out your vehicle's steering wheel and ignition module cover, inserting the key and turning it to the accessory position, and then sliding. If playback doesn't begin shortly, try restarting your device.
Connect the connector to the ignition switch. The first thing i need you to do will be to turn the ignition switch to the run position, and with your black test lead on a good ground, use the red lead to check all the fuses in the fuse box under the hood and see if you get 12 volts on both sides of the fuses with the fuses still in the fuse box. How do i replace the ignition switch cylinder?
On the back of the engine close to the firewall by the glow plug controller is a high pressure oil switch. Check if this fits your 2004 chevrolet silverado 1500. The ignition switch on a 99 silverado isn't just a switch.it's a small wire harness that in the colum & under the dash.if you look under the dash to the left of the colum.you will see a.
Please also check out the statistics and reliability analysis of the 2004 chevrolet silverado 1500 based on all problems reported for the 2004 silverado. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Three problems related to ignition switch have been reported for the 2004 chevrolet silverado 1500.
Ignition coil circuit wiring diagram 1999 2002 v8 chevrolet silverado gmc sierra. One of the first things we need to do to start this job is to remove our negative. If you think this is your problem,then copy and paste the link,watch the video below,ignition fix,or replace.
Check ignition switch where you stick the key in. You have to tap out one side to get out one gear, then tap the pin back through and do the same thing for the other gear. Be sure to make the hole large enough for you to insert.
Return the new switch for a replacement if the gear does not match the old switch. Stick the key in the ignition and turn the key back and forth jiggle and wiggle it and see if your igniting will make contact. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop.
You might need a puller to pull it loose after you loosen the nut. Then out comes the switch. Compare the old switch to the new ignition switch.
After you get it off look down in there and there is a small bolt that holds the switch in the column use a small light and you will see how it is held in there. If this switch goes out diesel fuel will not reach the injector pump.try pulling the molex and jumping it out with a wire.